1. Stm32 Array Declaration Form
2. Stm32 Array Declaration Codes
3. Stm32 Array Declaration Tool
4. Stm32 Initialize Array
5. Stm32 Array Declaration Code

In any microcontroller there is at least one general purpose input-output port. STM32 is a not different breed and as expected it also has several GPIO ports. These ports are usually named GPIOA, GPIOB, etc. but unlike most 8/16-bit micros these ports are 16 bit wide. Thus, in general, every port has 16 IO pins. Port pins have several modes of operation and this is what that makes them both robust and complex at first. In development boards the IO port pin naming is cut short and so we’ll find PA0, PB12, etc. instead of GPIOA0, GPIOB12, etc. Even in the reference manuals this short naming is used widely. In the end every I/O pin is general purpose in nature.

Key points with STM32’s GPIO

• Upon any reset event all GPIOs are floating inputs. This prevents any accidental damage to GPIOs in the event of emergency.
• All GPIO registers are needed to be accessed with 32 bit words. This is mandatory.
• Reserved bits for any GPIO register are kept at reset values i.e. 0.
• For every GPIO port there are seven registers but the only the first four are the most important ones. The rest can be ignored most of the times.
• These important GPIO registers per port are CRL, CRH, IDR and ODR. The rest three registers for GPIO ports can be avoided at the beginning.
• For bit set and for bit clear, operations REGx |= (1 << bit) and REGx &= ~ (1 << bit) respectively are very handy and efficient. However MikroC compiler provides bit level access though its internal header file coding like this GPIOB_BSRRbits.BS15. We can use this method or the other one.
• Some IOs are 5V tolerant and are label “FT” in datasheets and other docs. The rest of the I/O pins are not that tolerant and so 3.3V operation should always be ensured. STM32 has a maximum VDD tolerance of 4V but this value shouldn’t be used in any situation for safe operation. Best is to avoid 5V use with GPIOs whenever possible. This will help in avoiding accidental damage to the micro due to common mistakes.
• Unused GPIO pins should be kept at reset state or tied to ground with 10kΩ resistors so that they remain either as floating inputs or safely connected to ground though it’s not a must.
• I/O pins can source or sink currents up to 25mA. Thus direct LED drive is possible with them. To drive loads that need more than this value, we must use external BJTs, MOSFETs, optocouplers, transistor arrays or other driver devices.
• I/O pins should not directly drive inductive or capacitive loads.
• Care should be taken to avoid driving outputs beyond 50MHz. This is the maximum I/O pin frequency rating.
• CRL/H registers essential set GPIO pin operating mode independently as according to the table below:

• CRL sets GPIOs from 0 – 7 while CRH sets from 8 – 15. All IO ports are 16 bit wide unlike common 8 bit micros like PIC or AVR.

MikroC PRO for PIC General. Fig.1 UART Testing on STM32. STM32 microcontrollers are among the most widely adopted microcontrollers in the domain of embedded systems. They are power-efficient and have a small package size.

CRL Register:

CRH Register:

Previously we have tried to do a single conversion of one ADC channel. We were waiting for the ADC result in a loop, which isn’t an effective way of using processor resources. It is better to trigger a conversion and wait for the conversion to complete the interrupt. This way, a processor can do other tasks rather than wait for ADC conversion to complete. This time we will go through another example to set up more than one channel and read ADC values using interrupt service routine.

How does multichannel ADC conversion works?

If we need to convert several channels continuously, we need to set up Sequence registers (ADC_SQRx). There are three sequence registers: ADC_SQR1, ADC_SQR2, and ADC_SQR3 where we can set up a maximum of 16 channels in any order. Conversion sequence starts with SQ1[4:0] settings in ADC_SQR3 register. Bits [4:0] hold the number of ADC channels.

All 16 sequence channels can be set up the same way through all SQR registers. Then in the ADC_SQR1 register, there are four bits marked L[3:0] where you can set the number how many times sequence reading will be repeated.

Another thing we will have to take care of is to set up sample time for each channel. As we know, each channel in sequence can be set for different conversion times. The sampling time for each channel can be set up in two registers: ADC_SMPR1 and ADC_AMPR2. There are three bits for each channel in sequence.

If you use a standard peripheral library setting up multichannel ADC becomes an easy task.

Setting up multichannel ADC conversion with DMA write

Let’s write an example where we will read the first 8 ADC channels four times using scan mode. Then we calculate an average value of each channel and later print results on a terminal screen using UART.

We will write ADC values to memory by using a DMA channel. Once all data is stored in memory, a DMA transfer complete interrupt will be generated to trigger averaging and output. In the STM32F100x datasheet, we find that ADC pins are assigned alternate functions as follows:

Stm32 Array Declaration Form

• ADC1_IN0 – PA0
• ADC1_IN1 – PA1
• ADC1_IN2 – PA2
• ADC1_IN3 – PA3
• ADC1_IN4 – PA4
• ADC1_IN5 – PA5
• ADC1_IN6 – PA6
• ADC1_IN7 – PA7
• ADC1_IN8 – PB0
• ADC1_IN9 – PB1
• ADC1_IN10 – PC0
• ADC1_IN11 – PC1
• ADC1_IN12 – PC2
• ADC1_IN13 – PC3
• ADC1_IN14 – PC4
• ADC1_IN15 – PC5

Stm32 Array Declaration Codes

We will need to set up pins A0 to A7 as analog inputs for the first eight channels. Then we can set up an ADC conversion mode. Also, we need to set up Scan Conversion Mode to go through all channels selected in ADC1_SQRx registers. In the peripheral library, this looks like:

Then we must enable to enable continuous conversion mode as we want to cycle through channel list several times:

Stm32 Array Declaration Tool

Then we indicate the number of channels to be converted in scan mode:

The next thing is to indicate which channels and what order we need to convert. For this, we set up each channel individually with commands:

I’ve chosen to go all eight channels in the row from 0 to 7. But you can mess up the numbers as you like. The rest is to set up DMA where it copies ADC values to memory on each EOC event. After DMA copies a predefined number of values, it generates an interrupt. Then we can manipulate data as we like. As in our example, we average multiple instances.

Stm32 Initialize Array

This is a result on the terminal screen.

Stm32 Array Declaration Code

You can hook up a potentiometer or any other analog sensor to each channel to see its ADC value.

Working C code of multichannel ADC

Here is the complete main source code if you would like to analyze or use fragments for your purposes:

Also, you can download project files [STM32DiscoveryADC_DMAmultiple.zip] that compile with Codebench GCC and Eclipse.